[2017-July-News]Braindump2go 200-150 PDF and 200-150 VCE 106Q Free Offer[51-60]

2017 July CCNA 200-150 Exam Dumps with PDF and VCE New Updated in www.Braindump2go.com  Today!

1.|2017 New 200-150 Exam Dumps (PDF & VCE) 106Q&As Download:
http://www.braindump2go.com/200-150.html

2.|2017 New 200-150 Exam Questions & Answers Download:
https://drive.google.com/drive/folders/0B75b5xYLjSSNVmxoUEhTTmZZMXc?usp=sharing

QUESTION 51
The network administrator has been asked to give reasons for moving from IPv4 to IPv6. What are two valid reasons for adopting IPv6 over IPv4? (Choose two.)

A.    no broadcast
B.    change of source address in the IPv6 header
C.    change of destination address in the IPv6 header
D.    Telnet access does not require a password
E.    autoconfiguration
F.    NAT

Answer: AE

QUESTION 52
Switch A has BPDU fitering configured on all active interfaces.
A second switch, Switch B, is connected to Switch A.
Which two actions will Switch A take when Switch B is connected to it? (Choose two.)

A.    Switch A will not send any BPDUs.
B.    Switch A will transition the port a normal spanning tree port.
C.    Switch A will not accept any BPDUs
D.    Switch A will errdisable the port.
E.    Switch A will start sending BPDUs to Switch B.

Answer: AC

QUESTION 53
An engineer is configuring a new MDS switch. The switch is powered on, the customer connects to the console, and the initial setup script is started.
Which two items can be configured during this setup process?

A.    default port-channel mode
B.    default port VSAN membership
C.    default switch port interface state
D.    default zone mode
E.    default storage VDC

Answer: CD

QUESTION 54
Which Cisco UCS power policy mode enables a configuration that can tolerate the loss of an input power circuit?

A.    nonredundatnt
B.    Grid
C.    N+1 in normal mode
D.    N+1 in high-density mode

Answer: B
Explanation:
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/hw/chassis-install-guide/ucs5108_install.pdf (page 33)

QUESTION 55
What is the maximum working distance of a 1000BASE-ZE SFP transceiver when ordinary single mode fiber?

A.    up to 70 kilometers
B.    up to 40 kilometers
C.    up to 550 meters
D.    up to 10 kilometers

Answer: A

QUESTION 56
Refer to the exhibit. Which type of network communication is depicted?
 

A.    802.3 frame
B.    TCP frame
C.    Ethernet packet
D.    UDP packet

Answer: A

QUESTION 57
Which protocol is supported when OSPFv2 is used as the routing protocol?

A.    NetBios
B.    LAT
C.    IPv4
D.    IPv6

Answer: C

QUESTION 58
Which two port types are needed to build out an FCoE pass-through switch in NPV mode while maintaining Fiber Channel packet visibility? (Choose two.)

A.    VN Port
B.    VE Port
C.    VF Port
D.    Edge Port
E.    N Port

Answer: BD

QUESTION 59
A network design team has mandated that IP-only routing protocols be used in the network. Which two routing protocols will they want to use? (Choose two.)

A.    BGP
B.    OSPF
C.    RP
D.    EIGRP
E.    IS-IS

Answer: BC

QUESTION 60
What is the maximum of fabric modules that can be installed in a Cisco Nexus 7000 chassis?

A.    5
B.    6
C.    4
D.    7

Answer: A


!!!RECOMMEND!!!

1.|2017 New 200-150 Exam Dumps (PDF & VCE) 106Q&As Download:
http://www.braindump2go.com/200-150.html

2.|2017 New 200-150 Study Guide Video:
https://youtu.be/ySnz1PlssKA

         

Comments are closed.